How To Clean A Proheat Pet Bissel

Download Commodity

Download Article

Bissell upright carpet cleaners are a heavy-duty carpet cleaner for at-home employ. They are platonic for homes with lots of carpet, heavy traffic and pets.

1. 1

   Pretreat your carpet with a spray-on pet stain remover. This is best for discolored areas, heavy traffic areas or noticeable pet stains or smells. Leave it to sit while you prep the motorcar.

2. two

   Lift the handle from the water compartment at the front of the Proheat cleaner. Pull up and take the container to your sink.^[1]

   Advertisement

3. 3

   Pull the plastic lever on the back of the container and lift the top section out. You lot volition see a pigsty in the bottom part where the hot water volition go. Fill up with very hot water and replace the summit portion of the container.^[2]

   • Make sure the plastic lever snaps shut.
   • Supersede the plastic container on the front of the auto and release the handle.

4. four

   Remove the plastic solution container from the dorsum of the carpet cleaner. Take the container to the sink. Pour in the solution or a mix of solution and hot h2o, according to the directions on the back of the cleaning solution canteen.^[3]

   • Pay attention to the fill up line.
   • Supersede it on the back of the machine.

5. 5

   Set the dial on the front end of the machine to "floor cleaning" rather than "tools." Whatever time y'all use an zipper, you need to alter this setting.

6. 6

   Apply the punch at the elevation of the automobile to set the intensity of your cleaning, such every bit "rinse," "normal cleaning," or "heavy cleaning."^[4]

7. 7

   Remove all the furniture from the carpet you are about to clean.

8. eight

   Plug in the machine and start at the area furthest away from you. Starting at the edges and working toward the door will ensure yous don't tread on the newly cleaned rug equally it dries.^[five]

   Advertisement

1. 1

   Go to the first department of the carpet. You will work in small areas, cleaning several feet at a fourth dimension. Turn on the power button and the heater button.

   • The heater button helps the carpet dry out faster.

2. 2

   Step on the small lever on the bottom left edge so that the cleaner reclines and yous tin can push button it. Place the trigger on the handle. When you pull the trigger, cleaning solution is released.

3. 3

   Depress the trigger and push the cleaner forwards as far as you can comfortably achieve. Continue the trigger pressed down and bring the cleaner back toward you lot. This is referred to as a "wet pass."

4. iv

   Allow the trigger become and brand several "dry out passes" when the cleaner and water are not being used. Repeat until no more water is being pulled up.

5. 5

   Repeat until the area of the carpet is cleaned. ^[six]

6. six

   Switch the dial to "tools" to use the attachments to clean smaller areas. You lot will use the aforementioned general instructions with the brush as y'all would with the floor cleaner. Make a wet pass with the trigger depressed and then make several dry passes.^[7]

   • Remember to modify the punch to "floor cleaner" before y'all apply the upright role once again.

7. 7

   Allow the carpet to dry completely earlier replacing furniture and walking on it.

   Advertisement

1. 1

   Pay close attention to the dirty water in the front container on your Bissell cleaner. When it fills up, you will need to change information technology. Consider moving it to linoleum to reduce the chance that y'all will spill the muddied h2o on the carpet.

2. two

   Turn the cleaner off. Lift the handle and remove the water bowl. Pour the dirty h2o into the sink.

3. 3

   Refill the water basin with hot water. Cheque that y'all take enough solution to go along. You will modify the h2o tank more frequently than the solution tank.

   • Y'all volition need to modify the water several times for larger cleaning jobs.

   Advertizing

Add New Question

• Question

  Where tin can I find the Bissell Proheat Pet manual?

  

  This answer was written by one of our trained squad of researchers who validated it for accuracy and comprehensiveness.

  

  wikiHow Staff Editor

  Staff Answer

  If you've lost your original newspaper manual, yous tin can find user'southward guide online on the Bissell website. Do a search for "Bissell Proheat Pet user's guide" and download the PDF file to your computer or mobile device.

• Question

  What do I do if my Proheat Pet has no suction?

  

  This respond was written by i of our trained team of researchers who validated it for accuracy and comprehensiveness.

  

  wikiHow Staff Editor

  Staff Answer

  A loss of suction could hateful that the tank is cracked, the motorcar is on the wrong setting, or the nozzle is cracked or chock-full. Another problem could be that the tank lid isn't fastened right or the motor duct gasket screen is blocked by debris. Examine the various parts of your Proheat Pet to make sure that there are no problems in whatsoever of these areas.

• Question

  How do I clean my Proheat Pet?

  

  This reply was written by one of our trained team of researchers who validated it for accurateness and comprehensiveness.

  

  wikiHow Staff Editor

  Staff Reply

  Turn off the power and remove the h2o tank. Empty the tank and rinse it with hot tap water. Articulate any droppings from the lint trap and supercede the tank. Remove the menstruum indicator filter and rinse it, as well every bit the cap and rotor. Remove any loose hair or lint from the brush roll. To clean the outside of the motorcar, wipe it downwardly with a soft material.

• Question

  How do I clean the clear plastic front end intake chute?

  

  There are 2 Phillip caput screws on each side. You will need to unscrew them, lift upward the back, and it comes correct off.

• Question

  My cleaner is not releasing the cleaner solution or water, what should I practice?

  

  Re-seat the solution/recovery tank. Make sure on models with the little tiny dispenser (in addition to the tank/recovery saucepan) that you accept that filled. If this is not the issue, check to ensure in that location's non blockage in the path of the cleaner's spray. Finally, check to ensure that the sprayer power belt isn't broken or unseated.

• Question

  The front end of the cleaner is half broken off. Is in that location a replacement that can be installed?

  

  Get online and search for Bissell parts. It's all replaceable. If the front is even partially broken, the suction is significantly compromised.

• Question

  When I fill upward the formula tank, it comes right out of the bottom of the machine. How do I ready this?

  

  Sarah Battilana

  Community Respond

  It sounds similar a plug or slice of the cleaner might be missing or loose. Inspect the opening where the liquid enters the Bissell. Is there a red plug in place? If not, you may demand to get a replacement slice to foreclose the liquid from pouring out.

• Question

  How tin I get an possessor/user transmission?

  

  Sarah Battilana

  Community Respond

  Search online for your model of cleaner along with the words "user transmission." This should straight you lot to a PDF copy that yous can salvage for your records.

• Question

  My motorcar is not sucking up water. What should I do?

  

  Sarah Battilana

  Customs Respond

  Commencement, check to make sure that the dirty-h2o reservoir isn't total. Sometimes if information technology is or is close to the total-line, it won't suck up water anymore. If that isn't the problem, it's possible something is keeping the bristles from rotating fully. Check them out to see if something is stuck.

• Question

  What belt do I need for this, and can I become a replacement transmission if I lost the original?

  

  Sarah Battilana

  Community Respond

  Search online for your model of cleaner and the words "user transmission" to get an electronic copy. Depending on the model you take, you lot will need a specific belt. The user manual should dictate which one you need to gild.

See more answers

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertisement

• Prep your cleaner and modify the water on an like shooting fish in a barrel to clean surface, like a laminated kitchen flooring. The containers drip when inverse.

• Pay attending for clumps of hair that gather as you clean your floors. Pet and human pilus tin become embedded in the fibers. Remove the clumps and throw them away as yous find them. The carpet cleaner will non remove them.

Thanks for submitting a tip for review!

Advertisement

Things You'll Need

• Carpet cleaning solution
• Hot water
• Pretreating solution
• Sink

About This Article

Commodity Summary 10

To use a Bissell Proheat Pet, start by lifting the handle on the water compartment at the front of the cleaner and bringing information technology to a sink. Then, pull the lever on the back of the container and lift the top department out so you tin can pour hot h2o into the container. Next, remove the plastic solution container on the back of the cleaner and fill it with a mix of solution and hot water. Once you've placed both containers back on the cleaner, set the dial on the front to "flooring cleaning," choose an intensity, and plug in the machine. To learn how to change out muddied water in the cleaner, whorl down!

Did this summary assist y'all?

Thanks to all authors for creating a page that has been read 157,798 times.

Did this article assistance you?

Source: https://www.wikihow.com/Use-a-Bissell-Proheat-Pet

Posted by: smithcoulp1969.blogspot.com

Share this post